Lightning strike counter calibrator Usage Notice Seven points 1. Charge before use, in order to ensure the charging effect and prolong the battery life, you need to use a special charger. Empty battery to full Requires 3-4 hours, red light on the charger Light indicates charging; Green light indicates charging is complete. Before use, plug in the attached ground wire plug at the end and ground wire to ground.
2. According to the counter installation height, pull out the telescopic discharge pole properly.
3. Press the red button, turn on the high voltage for about 1 second, the indicator light (micro-flash), you can gently click the counter and the arrester connection for testing.
4. After each click, the end of the discharge rod should leave the counter. If you need to repeat the test, you do not have to release the button. When the indicator light flashes again after 1-2 seconds, you can click the test again.
5. Continuous test will cause the tester to heat, please pay attention to the appropriate interval time.
6. If the indicator light is still not flashing after pressing the button for more than 3 seconds, it means that the battery needs to be charged.
7. Do not disassemble the calibrator. If the battery capacity drops significantly or the charging efficiency is too low, you need to change. Please purchase a dedicated battery pack from the company.
Note: No part of the body can touch the electrode part when the indicator light is bright (micro-flashing), otherwise there is a danger of electric shock.
Lightning counter calibrator Usage method 1. Charge before use, in order to ensure the charging effect and extend the battery life, you need to use a special charger. Empty battery to full Requires 3-4 hours, the red light on the charger indicates Charging; The green light indicates that the charging is complete. Before use, plug in the attached grounding plug at the end, and the grounding clamps the ground.
2. According to the counter installation height, pull out the telescopic discharge pole properly.
3. Press the red button, turn on the high voltage for about 1 second, the indicator light (micro-flash), you can gently click the counter and the arrester connection for testing.
4. After each click, the end of the discharge rod should leave the counter. If you need to repeat the test, you do not have to release the button. When the indicator light flashes again after 1-2 seconds, you can click the test again.
5. Continuous test will cause the tester to heat, please pay attention to the appropriate interval.
6. If the indicator light is still not flashing after pressing the button for more than 3 seconds, it means that the battery needs to be charged.
7. Do not disassemble the calibrator. If the battery capacity drops significantly or the charging efficiency is too low, you need to change. Please purchase a dedicated battery pack from the company.
Note: No part of the body can touch the electrode part when the indicator light is bright (micro-flashing), otherwise there is a danger of electric shock.
2. According to the counter installation height, pull out the telescopic discharge pole properly.
3. Press the red button, turn on the high voltage for about 1 second, the indicator light (micro-flash), you can gently click the counter and the arrester connection for testing.
4. After each click, the end of the discharge rod should leave the counter. If you need to repeat the test, you do not have to release the button. When the indicator light flashes again after 1-2 seconds, you can click the test again.
5. Continuous test will cause the tester to heat, please pay attention to the appropriate interval time.
6. If the indicator light is still not flashing after pressing the button for more than 3 seconds, it means that the battery needs to be charged.
7. Do not disassemble the calibrator. If the battery capacity drops significantly or the charging efficiency is too low, you need to change. Please purchase a dedicated battery pack from the company.
Note: No part of the body can touch the electrode part when the indicator light is bright (micro-flashing), otherwise there is a danger of electric shock.
Lightning counter calibrator Usage method 1. Charge before use, in order to ensure the charging effect and extend the battery life, you need to use a special charger. Empty battery to full Requires 3-4 hours, the red light on the charger indicates Charging; The green light indicates that the charging is complete. Before use, plug in the attached grounding plug at the end, and the grounding clamps the ground.
2. According to the counter installation height, pull out the telescopic discharge pole properly.
3. Press the red button, turn on the high voltage for about 1 second, the indicator light (micro-flash), you can gently click the counter and the arrester connection for testing.
4. After each click, the end of the discharge rod should leave the counter. If you need to repeat the test, you do not have to release the button. When the indicator light flashes again after 1-2 seconds, you can click the test again.
5. Continuous test will cause the tester to heat, please pay attention to the appropriate interval.
6. If the indicator light is still not flashing after pressing the button for more than 3 seconds, it means that the battery needs to be charged.
7. Do not disassemble the calibrator. If the battery capacity drops significantly or the charging efficiency is too low, you need to change. Please purchase a dedicated battery pack from the company.
Note: No part of the body can touch the electrode part when the indicator light is bright (micro-flashing), otherwise there is a danger of electric shock.
Temporary Fence,Construction Site Fence Panels,Outdoor Fence Temporary Fence,Outdoor Temporary Fence
Anping Xinlong Wire Mesh Manufacture Co.,Ltd. , https://www.xinlongfence.com