Nowadays, many domestic households want to decorate their homes with a good design, especially the floor is the most vulnerable. If you don't have a good floor, it will be troublesome to start renovation. A lot of people have started to consult how to install solid wood floor springs , what steps and precautions are taken during installation. Share it for everyone today. Next, let Xiaobian bring everyone to understand what the installation steps of solid wood floor springs are.
Steps for installing solid wood floor springs:
1. Before laying the moisture-proof floor mat, firstly put a 0.2 mm thick PE moisture-proof film. The moisture-proof film needs to be laid flat, the joint overlaps 300 mm, and is sealed with 60 mm wide tape and compacted. The side of the wall is 30-50mm, but it needs to be lower than the height of the baseboard.
2. The thickness of the floor mat is not less than 2mm (preferably 3mm thickness). During installation, the mats should not overlap, the interface should be sealed with 60mm wide tape, compacted, the mat should be laid flat, and the wall edge should be 30-50mm, lower than the baseboard height.
3. Unpack the floor before paving, pre-paste the floor, separate the dark and light colors, and communicate with the customer. The end of the box is marked with red dots, and there are short plates inside. The first one is used when paving, and the long board is cut after the short board is used.
4. When the floor is paved, do not step on the floor. If you step on the floor, use the packing box to cushion the floor. During the paving process, the floor surface of the first row is measured, and the length of the floor at the end of the first row is measured. The short plate inside the package is first used under the premise of the expansion joint; the floor of the length of not less than 300 mm is used as the second row of the floor. The head is not less than 300 mm between the short seams of the adjacent two rows of floors; the width of the continuous pavement shall not exceed 6 m and the length shall not exceed 12 m. The transitional connection is required for the excess part, and the 8-12mm expansion joint is reserved for the connection part, and the T-shaped buckle is used for the entrance of the adjacent room.
5. The floor and any fixed objects in the room should be reserved for expansion joints. The floor around the water pipe should be glued to 4 to 5 places in the surrounding area; the floor covering requires moderate joints. In areas with high environmental humidity, floor coverings The gap of the installation is controlled at about 0.4 mm and measured with a feeler gauge.
6. Before installing the pavement, first determine the installation position of the buckle, and the buckle is perpendicular to the door sleeve to ensure that the buckle is stable and there is no sound. The last piece of each row and the last row of the floor of the room must be tightened with a hook hook; solid wood multi-layer composite The floor is generally made of glue-free paving method, and the expansion joint is spring-tight to avoid arching and separation. The length of the spring is 10mm, and the compressive elasticity in the natural state is 20 to 30 Newtons.
7. The moisture-proof pad lead-out part needs to be pressed between the spring and the floor. In the skirting line, it must not be over the top of the skirting line. If there is any excess, it should be cut off with a paper cutter, and the positioning wedge should be taken out and the spring piece should be installed. The long side of the floor is placed 100mm away from the end, and the short board can be placed in the middle.
8. Place one end at each end. If the end does not use a spring, use each floor end dispensing method in the paving process to install the baseboard. The seams are tight, the height is consistent, the fixing is firm, and the paving is completed. The service technician needs to conduct a comprehensive inspection of the paved floor to clean up the waste at the site.
The above solid wood floor spring content is the installation step of the solid wood floor spring shared by everyone today. I believe that everyone has already had a good reference after reading. In this small series, I am grateful to everyone for reading. Your reading is to give us the greatest support. If you want to know more, please continue to pay attention to the decoration home network.
More related wonderful reading:
What is the price of the floor spring? How to choose a ground spring?
What are the types of floor springs? What is the size of the floor spring?
What is the principle of the ground spring? What is the structure of the floor spring?
What is a spring floor? How about the spring floor?
How to install the floor spring? Floor spring installation process
Bathroom Sink Faucet,Bathroom Water Filter,Bathroom Water Tap,Brass Kitchen Faucet
kaiping aida sanitary ware technology co.,ltd , https://www.aidafaucets.com