Doors and windows are available in every household, and there is more than one, but for the common sense of installation of doors and windows, it is estimated that few people know that only professional installers know, let's understand the installation steps of door and window frames and door and window fans.
Door and window frame installation steps
The door and window frame installed first must be left in the head, and straightened straight when the main project is constructed to the window sill and floor, and temporarily supported by the diagonal support.
After the completion of the main structure, the rear-mounted door and window frame is reviewed after the elevation, size and position of the brick are correct.
When installing, fix the wooden window frame to the correct position in the door and window opening with wooden wedge. When installing, pay attention to hanging the vertical line in the vertical direction to ensure that the side of each floor window is on a vertical line, and every window on the same floor in the horizontal direction. The eyebrows and window sills are on the same horizontal line.
Door and window fan installation steps
First, measure the net size of the door and window frame, and consider the width of the seam, determine the height and width of the fan to be installed, and then draw the planing line. When drawing the line, try to ensure that the width is uniform.
If the size of the door sash is too large, it can be sawed and trimmed. When the door and window sash is double fan, first make a high and low seam, and press the left fan with the right fan in the opening direction.
If the size of the door sash is too small, you can add a strip on the bottom or use a glue and nail to tie the nailed wood strip on the side of the hinge. Note that the nail cap should be flattened and rushed into the strip 1-2mm.
For flanges that are susceptible to friction in frame contact, a 0.5-1 mm bevel should be planed.
When installing the window sash, use the wooden wedge to plug the bottom of the fan, check the gap, and draw the hinge position line after passing the test.
The distance between the hinge and the hinge installation position from the upper and lower ends of the door and window should be 1/8 of the full height of the door and window sash, and the opening is flexible.
Hardware should be fully installed, suitable for location and secure. All hardware is screwed in and fixed with wood screws. When the wooden doors and windows are made of hardwood material, you can drill the hole slightly smaller than the wood screw. The hole depth is 2/3 of the length of the wood screw. After driving in 1/3, screw it with a screwdriver. Into the remaining 2/3.
For doors that open the wall, it is advisable to install a door stopper.
Window wind hook installation should pay attention to make the opening angle of the upper and lower sashes consistent.
The installation of doors and windows directly affects the use of doors and windows later, it can also be said that it directly affects the service life of doors and windows, so the installation of doors and windows is not sloppy. [ Follow the WeChat public account "Jiuzhengmen Window Network"; pay attention to courtesy, scan code to send millions of business opportunities! Jiuzhengmen window network exchange group ]
A mudflap or mud guard is used in combination with the vehicle fender to protect the vehicle, passengers, other vehicles, and pedestrians from mud and other flying debris thrown into the air by the rotating tire. A mudflap is typically made from a flexible material such as rubber that is not easily damaged by contact with flying debris, the tire, or the road surface.
Mudflaps can be large rectangular sheets suspended behind the tires, or may be small molded lips below the rear of the vehicle's wheel wells. Mudflaps can be aerodynamically engineered, utilizing shaping, louvers or vents to improve airflow and lower drag.
custom molded Mud Guards are made from durable, rubber that's as tough as nails (or rocks for that matter). With a growing number of "No Drilling Required" applications, they're easy to install, conform perfectly to your fenders, and protect your ride and those around you from the rage of the road. Let them splash guards do the work.
Company information:
RenqiuXingcheng Rubber Products Co., Ltd. is located in the side of the Baiyang lake, our company is professional manufacturer of rubber products. We are one of the leading rubber company in china,The company is a private enterprise which is engaged in scientific research, production, sales and service and has obtained ISO 9001 certification. Our main business is producing all kinds of rubber products, including anti-skid plates, Rubber Sheet Series, Rubber Mat Series and horse mat series ect., The products are shockproof, anti-wear, anti-high and low temperature, anti-aging, oil resistant and chemical resistant in character.At present, our products have been sold at home and abroad and mainly exported to Canada, Germany, Chile, etc. We welcome domestic and foreign merchants to negotiate and cooperate with us. We are willing to join hands with old and new friends in creating a better tomorrow.
Rubber Mud Flap,Heavy Duty Rubber Mud Flaps,Rubber Mud Flap For Trailer,Truck Rubber Mud Flaps
Renqiu Xingcheng Rubber Products Co., Ltd. , https://www.xingchengrubber.com