â—† Ceiling connection must be handled with care
Ceilings are almost one of the must-do projects in modern home decoration. However, the cracking of ceilings is a problem that many owners have to face after they have been renovated for several years. Yu Tangyin believes that this is because some construction workers have not scientifically dealt with the connection of suspended ceilings. So soon after the renovation, the wooden parts of the ceilings began to crack. So how do you do construction to avoid cracks in the ceiling? It is understood that the ordinary ceiling connection is like this: two wooden planks are nailed to the wooden keel, and a distance of about one centimeter is left between the panel and the panel to connect with AB glue. If the seam stays large, the unevenness between the board and the board is obvious. It does not look good. If the gap is small, the strength of the bonding is not enough, and the board is easily cracked. In fact, a more reasonable method is to cut the connection planes of the two plates obliquely, put them together in a "V" shape, and inject AB glue in the middle. This way, not only the seams are dense, but also the pulling force is large enough. Then, the seams are sealed with kraft paper so that even if the temperature and humidity change, the ceiling will not crack.
â—†The balcony should not do too much ceiling
Some families have large balconies, so they hope to be more sophisticated and make the balcony an independent space. However, insiders suggested that the balcony is less for ceilings. This is mainly due to the large temperature variation of the balcony, the wood is easily affected by the temperature for a while to shrink for a while to expand, long time the joint is easy to crack, it seems to affect the appearance. The cracking of the ceiling is originally a construction problem. Even the best construction must undergo the test of cracking. Therefore, if the ceiling of the balcony is to be decorated, nailing plaster lines will be appropriate.
â—† Do a good job of moisture-proof engineering
Wood is easily deformed by moisture, which almost everyone knows. However, how to do the moisture-proof process of woodwork, most owners have no heart. Yu Tangyin, the manager of a company's engineering department, believes that doing a good job of preventing moisture will have a very important significance in improving the service life and aesthetics of woodworking. Therefore, every owner should take this moisture barrier. First of all, wood products that come into contact with walls and floors should be protected against moisture. In particular, the back of the door and window cover, the back of the wall shape, the back of the foot line, the back of the cabinet on the bedside table of the wardrobe, and the wood products of the bathroom should be protected from moisture very cautiously. If you can, it's best to do more detailed moisture protection on the back of your wardrobe. In addition to applying a layer of moisture-proof paint on the wall, a layer of plastic foam film can also be glued on the back of the cabinet so that the moisture can be kept “outside the doorâ€.
It should be noted that the moisture-proof coating should be applied as far as 1 cm beyond the outer edge of the wood product.
Ceiling Mount Aisle Ceiling Living Room Ceiling Coating Bedside Home Decor Window Space Large Wardrobe Toilet Ceiling Bathroom Door
Unshielded twisted pair (UTP) cat 5e cable, 500ft in easy pull box. It is ideal for high-end solutions such as Gigabit Ethernet, or digital CCTV cameras installation utilizing Cat 5e-type cable. This cable consists of 4 unshielded pairs of 24 AWG solid bare copper conductors, white PVC jacket. Stable electrical performance to 350MHz, exceeds requirements of TIA/EIA-568-B and ISO/IEC 11801. CMR riser rated.
Num:
ID-CA5F-PVC/LSZH
Item:
Cat5e 4-pair FTP LAN cable roll 305 mtrs
Brand:
Idex
Conductor :
Solid bare Copper
AWG :
24
Conductor Diameter (mm) :
0.51
Insulation :
Foam – skin PE
Average thickness(±0.03 mm) :
0.22
Min point thickness :
0.18
Insulation Dia(±0.03 mm) :
1.02
Twisting lay length(mm) :
30 undemeath
Twisting lay length(mm) :
200 undemeath
Jacket :
PVC/LSZH
Average thickness :
0.5
Min point thickness :
0.43
Outer Dia(±1.00 mm) :
6.0
Rip cord :
Yes
Weight Nom(kg/km) :
42
Core color:
Pair 1 :
Blue-White/blue
Pair 2 :
Orange-White/orange
Pair 3 :
Green-White/orange
100Mbps TP-PMD.52/155 Mbps ATM (ATM forum);
100BAST-T4 (fast Ethernet);
100 VG-Any LAN (IEEE 802.12);
100BAST-T (fast Ethernet);
1 Gbps Ethernet (IEEE 802.3).
CENELEC EN 61156-6;
CENELEC EN 50173-1;
CENELEC EN 50288-5-1, CENELEC EN 50288-5-2;
Flame retardancy is verified according to IEC 60332-1-2.
Pair 4 :
Brown- White/brown
Cable Applications :
POTS.T1&T1 fractional, ISDN basic & primary rate;
4/16 Mbps token ring (IEEE 802.5).10 BAST-T (IEEE 802.5);
Standard compliances :
All proposed category 6 requirements as per ANSI/TIA/EIA, ISO/IEC, and CENELEC EN Standards;
ANSI/TIA/EIA 568-B.2-1 CAT 6;
ISO/IEC 11801 CLASS E 2nd Edition;
Network Wire,Network Cable,Aluminum Network Wire,Network Wire For Cctv Camera
Shandong Shinaian Trading Co., Ltd. , http://www.cnpcworld.com