Cabinets are an important part of the kitchen. Modern kitchen cabinets make traditional Chinese mess kitchens neat and tidy. The kitchen cabinets combine the work area, storage area, and dining area of ​​the kitchen. Therefore, the space is used rationally, that is, judgement. Sets cabinets with good and bad standards.
Love House Cabinets Berg Cabinets
Goal: A convenient working environment
The three most important activities in the work area: side dishes, cooking and cleaning.
â–² side dishes: absolute need to maintain a distance of 80 mm between sink and stove, 100 mm better. This is the center of the kitchen: fish, meat, vegetables, etc. are all ready here. The required cooking utensils and seasonings should be kept within easy reach.
â–²Note: From a safety point of view, drawers should not be placed directly around the stove. Children will pull the drawers out of the ladder and climb to a height. This will cause injuries to the hot pot.
â–² Washing: The most common combination of sinks and drain pans is: Two sinks are 340 mm and 293 mm wide, mounted on a 800 mm wide cabinet. Close to the sink should be: closets for cups, dressing boxes, glassware and plates; closets for cooking utensils such as nets and dishes; drawers for utensils, cutlery, etc.; for decontamination, detergents or other chemicals The cleaning agent is located in the bottom cabinet under the sink, which is also the best place for the built-in trash can. Because children can open this cabinet, it is wise to lock the cabinet.
Goal: Comfortable equipment
â–²Lighting: It is more important to install light-adaptive lights in place than high-wattage lights. The daylight in the countertop area should come from the ceiling lights in the kitchen and the lights installed on the front of the closet. The important point is that the light is not reflective on the work surface, and it is properly shielded by a covering like a curtain box under a closet so that the eyes are not directly exposed to light.
â–² Sight: Wall cabinets, range hoods or light boxes should not block the user's eyes, so that he can not see the things behind the table. It is very important to keep the distance between the work surface and the bottom of the closet. 50 cm is generally enough.
â–² Take the height: The commonly used cookware should be placed within easy reach. The take-up height should be set to the height that the user's hand does not have any steps under the feet after stretching. The height of the highest cabinet of a wall cabinet that a person with a height of 165 cm can reach is about 190 cm. Older people will find it difficult to bend over and squat. Pull-out decks or baskets make it easy to pick and place things. Those who can only work in a sitting position have more restrictions, so the kitchen storage space designed for wheelchair users should be carefully considered.
Goal: Loose dining area
â–² A good rule: The suitable table should be 90 cm wide, and 85 cm of free space should be left on both sides of the table for the chair and body. Therefore, the total width of 260 cm is required. At least 240 cm is also required, with a 80 cm wide dining table. The distance between the dining chair and the closest cupboard is 60 cm, while the distance to the stove is 75 cm. From the end of the table to the closest cupboard should be 90 cm, while the range from 100 to 120 cm.
â–²Note: The door also takes up some space.
Cabinets Space Tables Lighting Glass Hoods Drawers Cabinets Doors Cabinets Doors Glass Cabinets Cabinets Glass Doors Closet Doors Kitchen Doors Cabinets Glass Tables Glass Tables Closet Kitchen Glass Sliding Doors
The spring has the characteristics of extensibility and compression, it can absorb and release the bounce when the vehicle passes through the uneven road surface, reduce the bounce range of the vehicle, and make the wheel keep contact with the road surface as much as possible. The energy produced during the stretching process is converted into heat by the shock absorber and diffused into the air.
The basic introduction of progressive springs the original car models usually use progressive springs, which are of a different thickness and density, the advantage is that it can absorb the fluctuation of the road surface through the part with lower elastic coefficient when the pressure is not big, and ensure the comfortable feeling of riding. When the pressure increases to a certain extent, the spring of the thicker part can play the role of supporting the car body, but this kind of spring`s shortcoming is the control feeling is not direct, the accuracy is poor. The basic introduction of linear spring the thickness and density of linear spring from top to bottom are invariable and the elastic coefficient is fixed. This kind of spring can make the vehicle get more stable and linear dynamic response, which is helpful for the driver to control the vehicle better. It is often used in performance-oriented modified vehicles and competitive vehicles. In other cars and cars, a smaller, softer secondary spring is added to the harder linear spring, which in addition to increasing comfort reduces the force of the spring when the main spring is pressed back, prevent the main spring from disengaging from the spring seat. Short spring introduction short spring is shorter than the original spring, and more robust, the installation of short spring, can effectively reduce the body center of gravity, reduce the roll when cornering, making cornering more stable and smooth, improve vehicle cornering handling. The damping setting of the original shock absorber is biased towards comfort, so the short spring and the original shock absorber are not very stable in coordination. It can not effectively restrain the rebound and compression of the short spring. When driving on a bumpy road, there will be an uncomfortable feeling of jumping, in the long run, the life of shock absorbers will be greatly reduced, and there is the possibility of oil leakage. Of course, these conditions are relatively speaking, the day-to-day driving would not have such serious damage, and try not to drive hard, after all, the original shock absorber can not withstand high load pressure. Replacing the short spring is the most economical way to reduce the height of the car body. It is a good choice for those who do not have a large budget. Of course, a price is a good price. The short spring has very limited improvement in handling performance, and there are still many disadvantages, so in the purchase must be clear about their purpose, or when the installation will not achieve the desired effect, resulting in unnecessary waste on the tragic.
Mould Springs,Spiral Torsion Spring,Double Torsion Spring,Stainless Steel Wave Washers
Nantong Safe Yawl Import &Export Co.,Ltd , https://www.ntsyspring.com